Space heater in an old house? What your wiring can handle, and the signs to stop
With oil near $6 a gallon, more cold rooms get a space heater. Here is why an old circuit is the weak link, the safety rules, and when to call an electrician.

When the oil bill climbs and one room never warms up, a space heater feels like the obvious fix. In an old house, the heater is rarely the problem. The wall it plugs into is.
I'm a builder in Somerville, and I see the same scene in older houses all over Greater Boston: a bedroom or back room, one heater, one tired outlet. Here is why that combination is risky, the rules from the fire safety agencies, and the signs that mean you call a licensed electrician now.
Why does a cold room in an old house tempt you to plug in a heater?
Old houses lose heat in odd places: a room over a porch, an attic bedroom, a back addition with thin walls. The heating system was balanced for a different house than the one you have now. Add a high oil price and it's easy to turn the whole thing down and warm one room instead.
As of the state's survey for the week of November 9, 2026, heating oil averaged $5.94 a gallon, which I covered in my post on what an old house can do about it. I understand the instinct. A heater can be a reasonable short-term tool. It just has to be used in a way the wiring can survive.
What is the heater actually asking of the wall?
Most portable electric heaters top out at 1,500 watts on their high setting. On a 120-volt household circuit, that is about 12.5 amps. A common electrician rule of thumb is to keep a load that runs for hours to about 80% of the breaker rating, which is 12 amps on a 15-amp circuit. Electricians treat a load that runs for hours as continuous and keep it to about 80% of the breaker rating. Treat that as a guide, and have an electrician check your actual circuit.
| Item | Typical number | What it means |
|---|---|---|
| Space heater, high setting | About 1,500 W, or about 12.5 A | Close to the limit of a 15-amp circuit all by itself |
| 15-amp breaker or fuse | 15 A | Often feeds several outlets and lights, sometimes in more than one room |
| Everything else on that circuit | Lamp, TV, phone chargers, a vacuum | Any of these can push the total over the line |
Check the nameplate on your heater for its wattage. Then think about what else is on the same circuit. In an old house, you often can't tell by looking, and the panel labels may be wrong.
Why is old wiring the weak link?
The breaker is there to stop an overload. But heat can build at a worn connection long before the breaker trips. That is why old circuits are the weak spot. These are the things I run into most:
- Shared circuits. In many older houses one 15-amp circuit covers several rooms. A heater plus whatever else is on will overload it.
- Worn or loose receptacles. A plug that falls out or feels loose has poor contact. Poor contact creates heat, and a heater draws current for hours.
- Extension cords and power strips. Thin cords and strips are not made for a heater's steady load. This is the most common mistake I see.
- Knob-and-tube wiring. Some attics and walls still have it. It was installed for much lighter loads than a modern household, and it has no ground wire. I cover it in my knob-and-tube and attic insulation post.
- Cloth-covered or aluminum wiring. Cloth insulation can turn brittle with age. Aluminum wiring, used in some homes mostly in the 1960s and 70s, can heat up at connections. A licensed electrician can tell you which you have.
- Old fuse boxes. Never put a larger fuse or breaker on a circuit to stop it tripping. The wire is sized for the original rating.
What are the safety rules for using a space heater?
These come from the U.S. Consumer Product Safety Commission, the National Fire Protection Association (NFPA) and the Massachusetts State Fire Marshal. They agree with each other.
| Rule | Why |
|---|---|
| Plug directly into a wall outlet. Never use an extension cord or power strip. | Cords and strips overheat under a heater's load. CPSC and the State Fire Marshal both say this. |
| Keep it at least 3 feet from curtains, bedding, furniture and anything else that burns. | Heat too close to things that burn is a leading way heater fires start. |
| Buy a heater tested by a recognized lab, such as UL or Intertek (ETL). Look for automatic shut-off if it tips over. | Newer models have tip-over and overheat protection. |
| Turn it off and unplug it when you leave the room or go to sleep. | Fire agencies all say the same thing: no heater running while nobody is awake and watching it. |
| Use it as a temporary measure and on a flat, hard surface, away from foot traffic. | A heater on a rug or soft surface can tip or overheat. |
| No unvented fuel-burning heaters indoors. | Unvented kerosene and portable propane heaters are not permitted for residential use in Massachusetts because of fire and carbon monoxide risk. |
The numbers explain the urgency. CPSC says portable heaters are involved in an average of about 1,600 fires a year in the U.S., with about 70 deaths and 150 injuries (2020 to 2022 data, January 23, 2026 release). In Massachusetts, the State Fire Marshal reported more than 6,400 heating fires from 2020 to 2024, with eight deaths (November 13, 2025 release). NFPA's heating safety page carries the same core advice.
Which signs mean stop and call a licensed electrician now?
Don't wait for the end of the season. Unplug the heater and call if you notice any of these:
- An outlet, plug or cover plate that is warm, hot or discolored.
- A burning or hot-plastic smell near an outlet or the panel.
- Buzzing, crackling or sizzling from a wall or panel.
- A breaker that trips again and again, or lights that dim when the heater starts.
- Scorch marks, melted plastic or a plug that fits loosely.
If you see smoke or flames, get everyone out and call 911. Do not reset a breaker over and over, and do not open the wall or panel yourself.
Fuel-burning heat is a separate danger. Carbon monoxide has no smell. Heating equipment is the leading cause of CO at home, per the State Fire Marshal. Smoke and CO alarms belong on every level of the home, and the State Fire Marshal advises replacing smoke alarms after 10 years and CO alarms after 5 to 10 years, depending on the model. If a CO alarm sounds, get out and call 911 or your local fire department. Somerville's alarm rules are in my smoke and CO detector post.
Who does what: you, the electrician, or me?
| Task | Who |
|---|---|
| Choose a listed heater, plug it straight into the wall, keep 3 feet clear, turn it off when leaving or sleeping | You |
| Test smoke and CO alarms, check their dates, replace old ones | You |
| Look at a warm outlet, replace worn receptacles, trace circuits, check the panel, assess old wiring | Licensed electrician only |
| Add a dedicated circuit, upgrade the panel or rewire knob-and-tube | Licensed electrician, with a permit |
| Air sealing and insulation for the cold room, and scheduling it with the electrical work | Licensed builder or insulation contractor |
In Massachusetts, electrical wiring is licensed work. The state statute, M.G.L. c. 141, section 1A, requires a license for the business of installing wiring and devices. In Somerville, the city's Inspectional Services Department says a licensed electrician must apply for the electrical permit. I explain how that works in my electrical and plumbing permit guide. I won't walk you through wiring steps here, and you shouldn't try them. A good electrician will explain what they found and why.
Ask for an evaluation before the cold snap, not after the first tripped breaker. A panel upgrade is a bigger decision, and I wrote about it in my panel upgrade guide. I won't give a cost here, because it depends on the house.
What fixes the cold room so you don't need the heater?
A heater treats the symptom. The cause is usually air leaking in and heat leaking out. Here is the order I'd go in:
- Air seal the room first. Gaps at the baseboard, the attic hatch, the rim joist and around windows are common. Start with my air sealing and winterizing post.
- Insulate where it counts. Attic floors, knee walls and the ceiling under an unheated space matter most. Do not blow insulation over active knob-and-tube without an electrician's advice. See the Mass Save insulation offers.
- Look at a ductless heat pump. One efficient unit can heat that stubborn room and also cool it in summer. Mass Save's whole-home heat pump rebate is $2,650 per ton, up to $8,500, for installs through December 31, 2026, and drops to $2,350 per ton, up to $7,500, for installs on or after January 1, 2027 (Mass Save amounts as of November 9, 2026). Mass Save's whole-home rebate also requires the home to be sufficiently weatherized. Homes built in 2000 or later qualify, and the partial-home rebate has no such test. See what changes on January 1 and how heat pumps do in a Somerville winter.
- Plan the electrical side. Many heat pump installs involve checking the panel or adding a dedicated circuit. Ask the installer and a licensed electrician what your house needs.
Heat pumps use electricity, so check your bill. In Eversource territory, a seasonal heat pump rate can lower delivery charges from November 1 to April 30. Here's how to check that you're getting it. I'm not part of the Mass Save installer network. I help owners plan the work around the rebate and coordinate the licensed trades.
What should you do this week?
- Unplug any heater from a power strip or extension cord and plug it directly into a wall outlet.
- Check the plug and wall plate for warmth after 20 to 30 minutes.
- Move the heater at least 3 feet from curtains, bedding and furniture.
- Test every smoke and CO alarm, and check the manufacture date on the back.
- Write down which outlets feel loose or warm, and book a licensed electrician to look at them.
- Seal the worst drafts in the cold room. My Winterize Your Old New England Home guide has the full list.
Want a second set of eyes on a cold room?
I'm not an electrician, and I won't pretend to be one. What I can do is walk the house with you, find where the cold room is losing heat, and set up the sequence: electrician first for anything on the wiring side, then air sealing, insulation and heating. The walkthrough is free, and there's no pressure to hire me. Book a free walkthrough and tell me which room won't warm up.
Frequently asked questions
Can I plug a space heater into a power strip or extension cord?
No. CPSC and the Massachusetts State Fire Marshal both say to plug a space heater directly into a wall outlet. Cords and power strips can overheat under a heater's steady load.
Why does my space heater trip the breaker?
Most heaters draw about 12.5 amps on high, and an old 15-amp circuit often shares that load with lights and other devices. A tripping breaker means the circuit is being overloaded. Don't swap in a larger breaker. Stop using that outlet for the heater and have a licensed electrician look at the circuit.
Is it safe to leave a space heater on overnight?
No. The State Fire Marshal and CPSC both say to turn heaters off when you leave the room or go to sleep. Use a heater with automatic tip-over shut-off and keep it at least 3 feet from anything that burns.
Is knob-and-tube wiring OK for a space heater?
I wouldn't run one on it. Knob-and-tube was installed for much lighter loads and has no ground wire. A licensed electrician should assess it before you add a heater, and any insulation near it needs the same caution.
Can I use a propane or kerosene heater in my house?
Not in Massachusetts. The State Fire Marshal says unvented kerosene and portable propane space heaters are not permitted for residential use because of fire and carbon monoxide risks.
What should I do when a carbon monoxide alarm goes off?
Get everyone outside to fresh air and call 911 or your local fire department. Don't go back in until the fire department says it's safe.
See everything I do, how I price work and the towns I work in.
Read this next
Home Care & SafetyKnob-and-tube, vermiculite and other attic surprises: what to fix before you insulate an older Greater Boston homeOld wiring or gray pebbles in your attic? What knob-and-tube and vermiculite mean for insulating a Somerville, Cambridge or Boston home.3 min read · Keep reading →
Costs & BudgetsPanel upgrade cost in Massachusetts: going to 200 amps for heat pumps, EVs and inductionPanel upgrade cost in Massachusetts: national prices, why Greater Boston homes move to 200 amps, Somerville permits, utility steps and Mass Save help.4 min read · Keep reading →
Home Care & SafetySmoke and carbon monoxide detector rules for Somerville homes (selling or renovating)Selling or renovating in Somerville? What Massachusetts requires for smoke and CO alarms, where they go, and how to pass the Fire Department inspection.4 min read · Keep reading →
Home Care & SafetyHow to winterize a drafty house: an air-sealing and insulation checklist for Somerville, Cambridge and Greater BostonCold rooms and high heating bills? Find where a Greater Boston house really leaks (attic, basement, windows, outlets) and fix it before winter, step by step.3 min read · Keep reading →
Home Care & SafetyDo heat pumps really work in a Somerville winter? A builder's honest answerDo heat pumps keep a Somerville home warm in January? Cold-climate specs, weatherization, triple-decker layouts, wiring, and 2026 Mass Save rebates.4 min read · Keep reading →
Costs & BudgetsHeating oil is about $6 a gallon. What an old house can do before the next fill-upA standard tank fill has been reported at over $1,500. Here are five moves for an oil-heated old house, in order, plus the help that exists and what not to rush.8 min read · Keep reading →
























